Tuesday, December 13, 2011

String Art Tutorial (yayyy!)


Hey ya’ll! 
So I’m sure all of you out there are just as much addicted to Pinterest as I am, and may have seen the artwork that has inspired my tutorial today!  Now, if you don’t know what I’m referring to, here’s the link to person selling their work on etsy. (making your own will cost you about $10 or so.. just saying!)
http://www.etsy.com/listing/82924417/louisiana-state-university-love

Don't mind the white string and spray paint, along with the pink paint... I used this for a different project I was doing.. but the supplies still stay the same




Supplies needed:
1 12 inch by 12 inch piece of wood
1 ruler
white spray paint (optional)
some type of painters tape (I used Scotch)
acrylic paint to paint the board
1 paintbrush
a pair of scissors
a pair of needle nose pliers
a hammer
nails
a pencil or marker
some notebook paper
sandpaper
string
Here’s the thread I bought from Hobby Lobby
http://shop.hobbylobby.com/products/lizbeth-thread-261107/




I got the wood from Lowes for about $5 for 4 of them.. just go to the wood section and ask them to show you the 2 x 2 wooden boards and have them to cut it into 4, 1 x 1 boards

So go ahead and sand the wood...preferably outside or something.. but this sandpaper block made it so much easier and faster to sand with

Then I painted my board black with acrylic paint as a base coat.. let it dry, then took the board outside and propped it on an old flower pot and spray painted it black (I painted the other side as well)



So for the South Carolina state outline, I Google imaged “South Carolina state outline” and I picked this one to use for the outline:

& then clicked this one to see where exactly Columbia was in Richland county
THIS link below is PERFECT for the outlines (I found this after I found the original one I used)!  Once you click on the state, you can play with the magnification when it brings it up to print!
http://www.eduplace.com/ss/maps/states.html

Now, I didn't print the outline because it does not print out to the size I need to fit the 1 x 1 wooden board I used, so I like to use notebook paper because it's not as thick as computer paper to trace with.  I place the paper in the top left hand corner to make sure that the image is traced straight and I also use the lines on the paper to help with measurements.


As you can see, the paper isn't wide enough, so I had to add to it to fit the entire state





I then taped the papers together and added a piece of paper (it was scrap from cutting the other paper earlier) to the top right so the paper will be wider to fit the state











This is the heart I used
http://www.freeclipartnow.com/d/25689-1/heart.jpg





Then I just drew a line to cut off the excess paper











































Instead of hammering in the small nails first, I used the longer nail to make a hole, then I pulled it out and oput the shorter one in.  The longer nail can be found beside the nails I used in Wal-Mart in a different pack

When a nail is hammered in crooked, I used the longer nail to bend it back by pressing the side of it and pushing it straight using both hands (couldn't get a picture using both hands because I had to use one to take the picture)


Note: Do not hammer your nails as close together as mine are here.. try about the space between each line on the paper between each nail, but a little less..




I used the pliers to pull the nail out instead of the back of the hammer because sometimes it gets too cramped



finished! now start tearing off the paper...

My dog, Leila, watching all the action



tie the string in a knot, like so.

Here’s the thread I bought from Hobby Lobby
http://shop.hobbylobby.com/products/lizbeth-thread-261107/
pull taut and to the right of the nail..








when you're ready to switch to another nail in the heart.. follow this step and the next





keep doing this until you work your way back around to the starting point



at the end, you overlap the beginning nail like so


then take the string and wrap it around the nail a few times

then use the beginning string to tie a knot on the ending string..knot a few times.. then cut off

To hide the knot, I took some clear nail polish and stuck it to the nail under the group of string.. I'm sure there are other ways you might find that are easier

YAY DONE!!!!!!



2 comments:

  1. Loving this tutorial and your blog! :) I'm definitely going to have to try this soon...but with Georgia of course!

    ReplyDelete
  2. Thanks so much! :) just let me know when you get around to doing it if you have any other questions, I'll be glad to help!

    ReplyDelete